Exactly How to Remove and Also Change a Bathtub
Exactly How to Remove and Also Change a Bathtub
Blog Article
They are making several good pointers on the subject of How to Install a Bathtub as a whole in this article on the next paragraphs.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably tough project. If the old bathtub is easily accessible, the job can move easily; if you need to open a wall surface to remove the old bathtub as well as place the new bathtub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also fit attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This post will aid you install a brand-new bath tub in your shower room if you have actually already gotten a brand-new tub as well as do not need to transform the arrangement of your previous water system pipelines.
Your tools as well as product checklist must comprise the following:
Getting ready for the Installation
First of all, the supporting framework provided with the bath must be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to prevent strain on the bath tub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water. After doing so, activate the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bath tub up until the spirit level checks out level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other tap.
Activate the supply of water and examine all joints as well as new pipework for leakages and tighten them if necessary. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bath paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the tub should wait till the bathtub has actually been utilized at the very least once as this will certainly resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in place between the faucet and the sink. Protect the tap in place with the supplier provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall in between the bathroom and the tiling, leading to issues with wetness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that article about How to Install a Bathtub through an associate on another web property. Are you aware of somebody who is curious about Tools You Need to Install a New Bathtub ? Be sure promote it. I enjoy reading our article about Installing A Bathtub.
Get Estimate
Report this page